We realized that your billing location is USA.
Please note that your billing address should be in the same country as your buying location. Please select one of the options:
New Terms of Use
The Subscription Term will automatically renew for successive Subscription Terms unless either party notifies the other at least 60 days prior to the end of the then-current Subscription Term that it has elected not to renew. Any renewed Subscription Term will be the same length as the preceding term or 12 months, whichever is greater. The fees for any renewed Subscription Term will be the same as those in effect at the end of the preceding Subscription Term, unless Siemens notifies Customer about different future fees at least 90 days prior to the end of the then-current Subscription Term.
The UCA (or any successor terms) available at Universal Customer Agreement (UCA) in the version that is current 60 days prior to the end of the then-current Subscription Term will apply for the following Subscription Term. However, if your subscription is governed by a master agreement that you have executed with Siemens, then that master agreement will continue to apply for any following Subscription Term, and auto-renewal terms for the subscription specified in that master agreement will prevail.
In all cases, instead of any previous versions of Supplemental Terms, the applicable Supplemental Terms available at Supplemental Terms in the version that is current 60 days prior to the end of the then-current Subscription Term will apply for the following Subscription Term.
Additional terms and conditions agreed upon in the initial order form (including product-specific terms), as well as agreed payment terms, will remain in effect for any following Subscription Term.
To perform edge analytics, both Insights Hub Edge Analytics and Insights Hub Edge Analytics Engine are necessary. Use it with MindConnect Nano, Software Agent or any other supported Edge Device.
Product sheet
Insights Hub Edge Analytics
Provided by SIEMENS
Collect and analyze data at higher sampling rates on your edge devices and preprocess high dynamic signals before sending the aggregates to the cloud
Insights Hub Edge Analytics is an edge application that collects and preprocesses high and low frequency data, corelates the data and performs out of the box analysis as well. Additionally, custom KPI calculations can be designed using a large library of analyzing functions.
Insights Hub Edge Analytics makes it possible to perform Condition Monitoring and as a result receive valuable information like the health status of machines or the performance of a production process. After preprocessing, the calculated data is then uploaded to Insights Hub.
Condition Monitoring is used for condition-based maintenance of machines, processes, and complete plants. The intention is to avoid unplanned downtimes to increase production line and plant availability. Therefore, a cyclic or permanent measurement and analysis of data is performed. Physical quantities could for example include temperature, speed, torque, vibration, pressure or current. Here the performance requirements regarding sensors and connectivity are usually very high. This applies especially to rotating equipment, where mechanical vibrations are used to determine the condition. The vibration signal provides information about the load of a machine and evolving faults. Streaming data from manufacturing machines, industrial equipment, and other connected devices creates a massive amount of data. Preprocessing and analysis at the edge provides cost benefits and reduces latency.
Edge Analytics provides:
- Access Insights Hub Edge Analytics
- Usage of a freemium mode to configure an Edge Device to stream up to 5 data points for a repeatable 7 days period
Insights Hub Edge Analytics provides:
- Improved asset availability through predictive maintenance.
- Use of preconfigured KPIs as well as intuitive creation of customized workflows for KPI calculation
- Data preprocessing at the edge level: analysis, aggregation, filtering – and upload of the preprocessed data in order to visualize and analyze it further.
The Edge software can run on MindConnect Nano or any Industrial Edge enabled device:
- Acquisition of high dynamic signals from a variety of data sources – with sampling rates up to 46,875 kHz.
- Local data buffering in memory of the Edge Device for analysis and aggregation
- Vibration analysis with a highly scalable system.
- Operating state detection with Trigger Rules
- Usage of out of the box calculations for different categories
- Vibration KPIs: RMS, Peak-Peak, Zero-Peak, Crest Factor
- Vibration Frequency/Order Spectra: Spectrum Acceleration, Spectrum Acceleration Envelope, Spectrum Velocity
- General data statistics: Minimum, Maximum, Average, Peak-Peak, Rate of change (Dynamic)
- Range Check: Minimum Extent, Maximum Extent
- Periodic Data Upload
- Event Based Data Upload
- Connectivity: Condition Monitoring Systems (CMS1200), MindConnect for Data Sources (S7 PLCs with Put/Get, OPC UA Modbus TCP data, Modbus RTU (RS232, RS485, RS422), Rockwell Protocol
- Data visualization with the Complex Data Plugin for Operations Insight and Fleetmanager
- Data uploaded by Insights Hub Edge Analytics can further be processed with any out-of-the-box of custom application (data can be accessed via standard APIs)
Offering Overview
| Insights Hub Edge Analytics | Insights Hub Edge Analytics Data Points Upgrade |
|---|---|
| Access the Edge Analytics application in your Launchpad and configure and manage your edge devices for data collection and analysis at higher smapling rate, preprocessing high dynamic singals before sending output to Insights Hub | Configure 5 data points in your edge device for preprocessing |
Total: USD $0.00
Added to cart
- Collect and analyze data at higher sampling rates on your edge devices and preprocess high dynamic signals before sending the aggregates to the cloud.
- Combining the efficiency of Edge computing with the added power and capabilities of Insights Hub will allow customers to increase flexibility, save cost and unlock new smart manufacturing use cases.
Take a look
